小米电视TV L32M5-AD 主板标签 TPD MS348T PB793 扩容 此机非晶晨CPU 改完后不能直接通过双清来实现 扩容，
再写入底层时需要对其进行相应修改，如图所示 紫色部分是已经修改好的
8G 9000 可能
16G 9001 可能
32G 9003
64G 9007
128G 900F
256G 901F 可能
原机测试电源的的串口 TTL跑码
T_115200
AC_ON
UART_115200
AC_ON
MIU1_DQS-OK
BIST0-OK
BIST1-OK
A#_NOTICE: BL3-1: v1.1(debug):c25aa68
NOTICE: BL3-1: Built : 21:24:36, Jun 14 2017
INFO: BL3-1: Initializing runtime services
INFO: [Booting] mstar_send_magic_ATF 135
INFO: BL3-1: Initializing BL3-2
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x20100a3c
INFO: BL3-1: Next image spsr = 0x1d3
INFO: BIN1_32bit mode Jun 14 2017 21:24:35
INFO: R1 1fb00000
INFO: R2 2010155900000003
INFO: R3 91d040000
U
Relocation Offset is: 01700000
[AT][MB][start ub][675]
U-Boot 2011.06-00000-gcaecefa-dirty (Sep 14 2021 - 20:26:55)
msIR_Initialize
[SYS][Utopia]: Function = SYSOpen, Line = 1143, current resource pri_shm content is: 0
[SYS][Utopia]: Function = SYSOpen, Line = 1162, [SYS INFO] OPEN INSTANCE...
create instance at 293EAEA8 with private size 128 bytes at 293EAEF0
[MIU][Utopia]:
[MIU INFO] miu opencreate instance at 293EAF78 with private size 80 bytes at 293EAFC0
create instance at 293EB018 with private size 48 bytes at 293EB060
uboot held at [291DDF60~2AC00000],size=01A220A0
DRAM: 172 MiB
Now running in RAM - U-Boot at: 2A200000
eMMC: HS200 200MHz
eMMC 3.68 GB [75FFF8h]
In: serial
Out: serial
Err: serial
Net: No ethernet found.
MAC: 0x50: 0xA0: 0x9: 0x59:0xF0: 0x16
[CPU][Utopia]:
[CPU INFO] cpu opencreate instance at 293FB4D0 with private size 44 bytes at 293FB518
[CPU][Utopia]: CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[tu]: * *` *xV4
[AT][MBoot][Driver Init][814]
factory: user mode
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
no force panel type
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
Changelist: 24543697
============= set bootargs ===============
WDT is not Enable !!!setenv WDT_ENABLE 1 to enable it.
Hit any key to stop autoboot: 0
AC on
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
fore uup IRKey [0xFF]
fore uup u8KeyPad_KeyVal [0xFF]
WDT is not Enable !!!setenv WDT_ENABLE 1 to enable it.
AC on
bt_vendor_name = Realteck,bt_vendor_id= 0x5D00
mmc change mount : tvinfo
Size of file "rtl8723ds_config" from mmc device 0 partition tvinfo: 83 bytes
Loading file "rtl8723ds_config" at offset 0x0 from mmc device 0 partition tvinfo
83 bytes read
Read bt fw file: rtl8723ds_fw
mmc change mount : tvinfo
Size of file "rtl8723ds_fw" from mmc device 0 partition tvinfo: 59744 bytes
Loading file "rtl8723ds_fw" at offset 0x0 from mmc device 0 partition tvinfo
59744 bytes read
no recovery mod!
BT_MAC:50:A0:09:5A:B3:66
Write RTK BT_MAC:50:A0:09:5A:B3:66
mmc change mount : tvinfo
Size of file "wake_on_ble.conf" from mmc device 0 partition tvinfo: 119 bytes
Loading file "wake_on_ble.conf" at offset 0x0 from mmc device 0 partition tvinfo
119 bytes read
enter wake on ble!
mmc change mount : tvconfig
Loading file "/config/PM.bin" at offset 0x0 from mmc device 0 partition tvconfig
24575 bytes read
[PM][Utopia]: Wait for PM51 standby...........[PM][Utopia]: PM51 run ok...........CRC Check OPEN: 1
0x8301
PS：养成良好习惯， 开机前跑TTL看一下码 没有emmc 没有数据 不跑码！ 电流一闪即逝。